Can I disable the thermostat’s internal temperature sensor?
Can I disable the thermostat’s internal temperature sensor? If a remote temperature sensor is connected, yes. Navigate to Admin -> Thermostat Configuration -> Click on the thermostat. In the Temperature Settings block, change Temp Sensor to Disabled.
Can I disable or lock a thermostat’s Fan Button?
Can I disable or lock a thermostat’s Fan Button? Yes, but only technical support can adjust this configuration. What are the Disable Fan Button configuration options? No (default): keeps the thermostat’s fan button active. Yes: de-activates the thermostat’s fan button and removes the Fan status from the thermostat’s display. When is it common to disable […]
Can I “lock-out” compressors based on an outdoor temperature?
Can I “lock-out” compressors based on an outdoor temperature? Yes. Each Pelican thermostat has a configuration called Compressor Lockout*. You can use this configuration to prevent the thermostat from enabling the compressors once the outside temperature is below a configured value. *Note: The Compressor Lockout configuration is only available if your Pelican Solution has an […]
Can a Pelican thermostat control a multiple fan speeds?
Can a Pelican thermostat control multiple fan speeds? There are two scenarios for multiple fan speed control. Two Fixed Fan Speeds (High and Low): Pelican has found that controlling just the Low and High fan speeds provides all the control needed to maintain a proper room temperature and manage fan noise. Here are the configuration options: […]
Can a Pelican thermostat control a two-position actuator?
Can a Pelican thermostat control a floating actuator? Yes. There are three scenarios where a two-position actuator can be controlled by Pelican thermostat: Two-Position heating and/or cooling valve control for an Air Handler. Note: This configuration is only able to be enabled by Pelican technical support. For Hot Water or Steam Floating Valve Control: Wire the […]
Can a Pelican thermostat control a floating actuator?
Can a Pelican thermostat control a floating actuator? Yes. There are three scenarios where a floating actuator can be controlled by Pelican thermostat: Floating a heating and/or cooling valve control for an Air Handler. Note: This configuration is only able to be enabled by Pelican technical support. For Hot Water or Steam Floating Valve Control: Wire […]
What is the Temperature / Resistance value for a Pelican external temperature sensor?
Categories: Sensors Temperature Probes What is the Temperature / Resistance value for a Pelican external temperature sensor? Pelican external temperature readings are set to use 10K Type II thermistors where 10K = 77°F (25°C). Click here to download the spreadsheet. Temperature (°F) Resistance (Ω) -20.00 -19.95 -19.90 -19.85 -19.80 -19.75 -19.70 -19.65 -19.60 -19.55 -19.50 -19.45 […]
How do I install a Pelican Ethernet gateway?
How do I install a Pelican Ethernet gateway? Step 1: Before installing your Pelican Gateway, make sure you have an active Internet connection. This can be a cable, DSL, cellular, or even a dial-up connection. If you do NOT have an active Internet connection, you can use a Pelican GW400-LTE gateway, which runs on the […]
How do I change a Pelican gateway from static back to DHCP?
How do I change a Pelican gateway from static back to DHCP? Follow these steps to reset the gateway back to DHCP: Power down the gateway. Remove the Ethernet cable from the gateway’s Ethernet port. Power up the gateway. Look for a solid LAN light on the bottom of the gateway. Plug in the Ethernet […]
Does a Pelican gateway use Inbound firewall ports?
Does a Pelican gateway use Inbound firewall ports? No. Outbound Only connection Pelican does NOT require any Inbound firewall connections. Note: Outbound versus Inbound connections describe how two devices are able to establish their initial connection to create a communication path from a device inside of a building across the Internet to a device in the […]